If you’ve been driving a Honda lately, you may have noticed a new warning light on your dashboard. The Honda Smart Key System dashboard warning light is meant to notify drivers when the system is not working correctly. The Honda Smart Key System is a feature that allows drivers to unlock their cars by just holding down the button on the door handle.
However, if the system doesn’t work correctly, the warning light will come on and tell drivers to contact Honda customer service. This light is only meant to be used in an emergency; otherwise, drivers should ignore it and continue using their traditional critical method.
🎯Suggested article: Honda Motorcycle PGM-Fi Warning Light
What is the Honda Smart Key System?
The Honda Smart Key System is a feature that allows drivers to unlock their vehicle using only the key fob. The system uses a range sensor and an infrared transmitter to determine if the key fob is close to the car. The system will activate the car’s locks if the key fob is within range. If the key fob is not close enough to the vehicle, the system will illuminate warning lights on the instrument panel.
See also: Dashboard Timing Belt Warning Light
What is the Honda Smart Key System Dashboard Warning Light?
The Honda Smart Key System dashboard warning light may indicate a problem with your Honda’s intelligent key system. If you experience this warning light, follow the steps below to troubleshoot and fix the issue.
If you have a Honda Accord or CR-V, your car has a smart key system that allows you to open the door using just your vehicle’s remote control. To use this feature, you need to set up your Honda’s intelligent key system. When you first get your Honda, the dealership will allow you to connect your intelligent key system to your vehicle.
đź‘€Look at this:Â Honda Smart Key System Warning Light Reset
Problems with the smart key system can cause the dashboard warning light to come on. If this happens, follow these steps to troubleshoot and fix the issue:
- Check that all of the necessary accessories are connected to your Honda’s intelligent key system. These include the transponder chip, immobilizer chip, and learning module (if applicable). If any of these items are missing or not working correctly, it could be causing problems with your Honda’s intelligent key system.
- Reset your Honda’s intelligent key system by pressing and holding down both buttons on the inside door handle for about five seconds until the dashboard warning lights turn off. Make sure that all of your accessories are reconnected after resetting your Honda’s intelligent key system.
- Try removing and replacing just one accessory from your Honda’s intelligent key system at a time in order to isolate which one is causing it.
Read also: Honda Fit Dashboard Warning Lights And Symbols
When is a Dashboard Warning Light Activated?
The Honda Smart Key system warns the driver of an upcoming door lock issue when one or more warning lights are activated. Warning lights may be activated when the key is not in the ignition when a door is not fully closed, or when there is a low battery condition. When one or more warning lights are activated, it is essential to take action to prevent serious injury.
🎯Suggested article: Warning Lights After Changing Battery Honda Civic
How to Fix a Honda Smart Key System Dashboard Warning Light?
If your Honda Smart Key system dashboard warning light is on, there is likely a problem with the key system. This guide will show you how to fix the issue.
Start by checking all of the components in the critical system. Ensure there are no bent or broken wires, all the fuses are intact, and the relays are working correctly. If everything looks good, you may need to replace one or more of the components in the critical system.
To replace a component in the critical system, start by removing the cover plate on the back of the intelligent key box. On some models, this plate has four screws that hold it in place. Once it’s removed, you’ll see two black relays and two white relays inside.
To replace a relay, first, take off its cover plate. Then remove its six screws and unscrew it from its housing. You can then replace it with a new one by reversing these steps. Be sure to put everything back together correctly before re-installing the cover plate!
If all of your components look good and there is no apparent issue with your wiring, you may need to reset your intelligent key system. To do this, turn off your car and remove all your keys from the ignition (except for one). Next, open your car’s door and press and hold down both buttons on the driver’s side dashboard until you hear an audible beep (about 5 seconds).
If you are having trouble with your Honda Smart Key System, be sure to check for a dashboard warning light. This lights up when there is a problem with the system and can help you get it fixed ASAP.
🎯Suggested article: Honda Fit Years To Avoid
FAQs About Honda Smart Key System Dashboard Warning Light
What does an intelligent critical warning light mean?
The Warning Light on the instrument panel is accompanied by an internal buzzer and possibly an exterior one. If three external buzzes are present with the light, it indicates that a door has been opened and closed while the vehicle was turned on but without the electronic key in its presence.
What does the key with an exclamation mark mean on Honda?
This image indicates an issue with the Smart Key Entry System. If illuminated, it is likely that either the Vehicle Stability Assist® (VSA®) system or the Hill Start Assist system is not operating as intended. Addressing this as soon as possible is essential for optimal performance and safety on the road.
What does a car with a key symbol on the dashboard mean?
This symbol on the dashboard indicates that the anti-theft system is in use. Acting as a confirmation, it signals that the security systems are actively operating and providing protection for the vehicle.
What does a key light with an exclamation point mean?
This indicator appears as a key with an exclamation point through it. When illuminated green, it signifies that the correct key is inserted in the ignition and the engine can start. If observed flashing, this denotes that the battery of the key needs to be replaced.
Aslaam u alaikum
Dear smart key system warning light is on….and getting off. Please tell me how it will be??
Smart key system light is not getting off.
Dear User,
The Honda Smart Key System Dashboard Warning Light is a feature in many modern Honda vehicles that uses a keyless entry and ignition system. This warning light is designed to inform you of issues related to the smart key system in your vehicle.
If the smart key warning light on your dashboard is turning on and off, there could be a few possible reasons:
Low battery in the smart key fob: The most common reason for this warning light to appear is due to a low battery in your smart key fob. Replace the battery in the fob, and the warning light should stop appearing.
Interference: Occasionally, radio frequency interference can cause issues with the smart key system. Make sure there are no devices emitting strong radio signals near your vehicle.
Damaged smart key: If your smart key has been damaged or exposed to extreme temperatures, it might not function properly. In this case, you may need to get a replacement from your Honda dealer.
System malfunction: If none of the above solutions work, there might be a malfunction within the smart key system itself. In this case, it is best to visit your local Honda dealer for diagnostics and repair.
In conclusion, if your Honda Smart Key System Dashboard Warning Light is turning on and off, it is important to address the issue by checking the battery, looking for potential interference, and visiting your Honda dealer if necessary.
Good evening
My name is O’Duaine
Can you advised me how to clean the check key light in the 2011 Honda Inspire please
Good evening, O’Duaine. Nice to meet you. The check engine light in your 2011 Honda Inspire can come on for a variety of reasons, and it’s important to properly diagnose the issue to ensure the light is properly cleared. Here’s a step by step guide you can follow:
Diagnose the Problem: To start, you will need to understand why the light came on in the first place. You can do this by using an OBD-II (On-Board Diagnostics II) scanner. This tool will provide a code that corresponds to a specific vehicle issue.
Check for Obvious Problems: Before using the OBD-II scanner, check for obvious problems such as a loose gas cap or other simple issues that might have triggered the light.
Use an OBD-II Scanner: If there are no obvious problems, connect an OBD-II scanner to the diagnostic link connector (DLC) in your car. This is usually located underneath the dashboard, on the driver’s side. Once you’ve connected the scanner, turn on the ignition but do not start the engine. Follow the instructions on your scanner to read the error code.
Interpret the Code: Once you have the code, look it up online or in the vehicle’s service manual to understand what the issue might be. These codes typically start with a P and are followed by four digits.
Fix the Issue: Based on the code, you’ll need to fix the underlying issue. This might be something you can do yourself, such as replacing a faulty sensor, or it may require professional assistance.
Clear the Code: After you’ve fixed the issue, you can clear the code using your OBD-II scanner. This should turn off the check engine light. If the light comes back on, there may be additional issues to address.
Remember, while it might be tempting to just clear the light without addressing the underlying issue, this is generally not a good idea. The check engine light is a signal that something is wrong with your vehicle, and ignoring this could lead to more serious problems down the line.