Many Jeep Grand Cherokee owners have experienced issues with their 4WD system. In particular, problems can come up after resetting it. Fortunately, there is a way to resolve this issue. This article will provide a guide on Jeep Cherokee Service 4wd System Reset.
Firstly, it’s important to understand what the 4WD system does and how it functions. The 4WD system is designed for enhanced traction in all conditions by allowing front and rear wheels to spin at different speeds. However, if the wheels become out of sync, some problems may occur when driving your Jeep Grand Cherokee, such as reduced maneuverability or difficulty gaining traction in slippery areas.
Once you are aware that the problem is related to an out-of-sync wheelset, you can follow these steps to reset your Jeep Grand Cherokee’s 4WD system: Firstly, turn off all electronic systems like air conditioning or climate control; next, put your car into neutral; finally start the engine and slowly accelerate until reaching 10 mph before slowly decelerating until coming back down below 5 mph – this should do the trick! If not, further investigation might be necessary from a mechanic or service provider specializing in Jeeps.
Follow these steps to reset the 4WD system of your Jeep Grand Cherokee:
- Step 1: Turn off your Jeep Grand Cherokee’s engine.
- Step 2: Disengage the 4WD system.
- Step 3: Locate the 4WD system’s fuse box.
- Step 4: Remove the fuse for the 4WD system.
- Step 5: Wait for 10 seconds.
- Step 6: Replace the fuse for the 4WD system.
- Step 7: Start your Jeep Grand Cherokee’s engine.
- Step 8: Engage the 4WD system.
- Step 9: Test the 4WD system to ensure it works properly.
If following these steps does not resolve the issue properly, it is recommended that a professional mechanic inspect the Jeep Grand Cherokee’s 4WD system for further diagnosis. We hope this article has been useful in teaching readers about Jeep Cherokee Service 4wd System Reset.
⚡️Another article: Hardwire Jeep Jk Dash Cam
Most Common Symptoms For 4WD Problems In Jeep Grand Cherokee
The Jeep Grand Cherokee is not immune to 4WD system malfunctions, and drivers should be aware of the potential symptoms and problems that may arise over time. Common issues with the 4WD system of a Jeep Grand Cherokee include grinding noises when turning or accelerating, difficulty shifting between gears, slow response times upon acceleration, and vibrations from underneath the vehicle.
4WD Warning Light
The 4WD warning light is one of the most common indicators of a problem with the four-wheel drive system. It is important to take action if this light comes on and have a qualified mechanic inspect the system.
4WD Lockup
When a 4WD system is not operating correctly, another common symptom is 4WD lockup. If the driver notices that the 4WD has locked up while driving, it is essential to immediately pull over and shut off the engine. Once this precautionary measure has been taken, it’s important to contact an experienced mechanic to inspect and repair the system as soon as possible.
💥See also: Jeep Compass Years To Avoid
4WD Noise
If your 4WD system exhibits symptoms, noise is one of the most common signs. This noise can range from clicking to grinding and should not be ignored. If you hear this sound, it is important to have the system examined by a qualified mechanic as soon as possible to avoid further damage or an accident. Ignoring these noises could cost you far more than a simple inspection.
4WD Vibration
If a 4WD system is not functioning correctly, one of the common symptoms is a vibration. This can be felt through the steering wheel, seat, or floorboard, and an experienced mechanic needs to check out the system if this symptom occurs.
4WD Slipping
If a customer is experiencing 4WD slipping, this could indicate a problem with the system. It is essential that the engine is turned off immediately and a qualified mechanic is contacted for further assessment. Suppose there are any other symptoms related to the 4WD system. In that case, a professional should also check it out as soon as possible to ensure proper functioning and safety.
Recommended article: Red Car With Key Symbol On Dashboard
How To Reset Jeep Grand Cherokee Service 4WD System
The Jeep Grand Cherokee is a powerful off-road vehicle, and when equipped with the Service 4WD System it offers an unbeatable performance. However, like any other system, it will eventually need to be reset. To help owners accomplish this task, step-by-step instructions should be followed.
First and foremost, users should locate the fuse box on their vehicle, usually found under the hood, but if not, then consult your owner’s manual for further details. Once located, seek out the designated fuse for the Service 4WD System, which should be labeled accordingly. The next step entails disconnecting the battery to ensure no power is going to this particular system while you’re working on it.
When finished disconnecting the battery, one can look for the reset button, which typically lies on or near a dashboard of sorts; again, consult your owner’s manual if unable to find it yourself. Upon locating said button, hold down for around five seconds before releasing – after this process has been completed successfully, you can rest assured that your off-road vehicle will now operate optimally once more!
⚡️Another article: Jeep Wrangler Subwoofer Box Plans
FAQs About Jeep Cherokee Service 4wd System Reset
Why does the Serv 4WD indicator illuminate?
When this light shows up, it’s signaling a potential issue with the 4WD mechanism. It might also be due to a gear shift that needs to be fully completed.
How can one reset the service alert on a 4WD Jeep Grand Cherokee?
Find the button marked “STEP” on the vehicle. Cycle through using the “STEP” button until a menu displays the miles remaining before service. Then, pressing and holding the “RESET” button should clear the “Perform Service” alert.
What’s the implication of a “Service 4WD System” alert?
This alert points to a malfunction within the 4WD system that requires attention. Typically, after starting the vehicle and moving the ignition key from OFF-RUN-START back to RUN, the 4WD light should briefly appear for a second or two and then vanish.
What does the serv 4wd alert signify on a Jeep?
When this alert is active, the vehicle operates 2WDn 2wd, turning off the 4WDe 4wd function. The cause might be software-related, a faulty sensor, or other issues. For instance, there was an instance where this alert appeared after a lift kit installation damaged the ABS sensor.